Outdoor LED floodlight accessories: brackets, recessed housings and IP67 connectors for professional installation

Outdoor LED floodlight accessories are the part that does not come in the box with the unit: the bracket, the recessed housing and the connector, all with the outdoor floodlight compatibility needed to fit them without adapting anything.

Wall brackets for LED floodlights

The wall LED floodlight bracket moves the unit away from the wall and aims the beam at the facade. The galvanised steel outdoor bracket withstands the weather without rusting, and the adjustable angle wall bracket sets the final tilt on site.

100cm bracket for facades and walls

The 100cm wall LED floodlight bracket is a black arm with fixing plates. The LED floodlight arm bracket moves the unit a metre off the wall, just enough for the beam to graze it. The wall LED floodlight bracket price changes with the model. For columns there are brackets for 1-2 and for 1-3 floodlights.

IP65 ground recessed housings

The outdoor recessed ground housing is set in the pavement and leaves the unit flush. IP67 recessed ground installation is the uplighting technique.

Housing for GU10 recessed fittings

The GU10 IP65 recessed ground housing is grey steel and takes any GU10 spotlight. Anyone looking for an aluminium recessed ground housing lands on that IP65 GU10 recessed housing, also in a 112 mm version. The recessed ground LED housing price depends on the diameter.

Models for garden floodlights

In gardens the most requested outdoor LED floodlight accessory is the housing, because it protects the unit from soil and irrigation. Water and impact resistance matters where people walk.

IP67 weatherproof connectors for outdoor use

The outdoor IP67 cable connector seals the joint that the conduit leaves in the open air. The ones in the catalogue are IP68, so the IP67 submersible connector certification and the IP67 protection are both covered. The IP67 weatherproof male female connector screws shut over the gasket, and the cable weather protection works without tape or resin.

Type I connector for straight joints

The IP67 type I T X connector covers the three usual joint shapes, and type I joins two cables in line to extend the cable run to the unit.

Type T and type X connectors for branches

An IP67 cable branch joint is made with type T for three cables and with type X for four. The IP67 weatherproof connector installation in X splits one line between several units with no inspection chamber.

How to choose the right accessory for your floodlight

First you decide where the unit goes, because that settles whether you need a bracket or a housing, and then you check the cable cross section, which determines the connector. The outdoor floodlight installation accessory comes last.

Professional installation with maximum protection

A badly sealed joint is the most common fault in outdoor lighting. Sealing the electrical connections with the outdoor floodlight complement accessory is cheap next to reopening a trench, and the outdoor IP67 cable connector gives a safe electrical installation with a long service life.

Complete the order with the outdoor and garden LED floodlights or with the AVANT series LED floodlights.

Frequently asked questions about outdoor LED floodlight accessories

What wall bracket do I need for my outdoor LED floodlight?

It depends on how far you move the unit off the wall. To graze a facade you want the 100 centimetre arm, and against the wall the unit's own stirrup is enough.

Do ground recessed housings withstand vehicles driving over them?

The IP65 steel housings are meant for foot traffic and garden areas. If a car is going to pass, check the admissible load before setting them in concrete.

What type of IP67 connector do I need outdoors?

Type I for two cables, type T for three and type X for four, and the cross section matters as much as the shape, so check that it takes the usual 2.5 square millimetres.

Are IP67 connectors submersible in water?

IP67 allows temporary immersion, not permanent, and the ones in the catalogue are IP68 and do withstand being under water, although the sensible thing is still to keep the joint out of it.

Can I fit a ground recessed housing with any GU10 floodlight?

Yes, as long as the lamp is GU10 and fits the housing diameter. Check the lampholder height, because some spotlights will not go in.